MESEP RE Surface Detectors for Conveyor Systems

Metal Detectors for Conveyor Systems Surface metal detectors for conveyor belts are electronic devices for detecting the presence of unwanted metal contamination in items moving along a conveyor belt. If you're worried about metal contaminants entering your process, and the conveyed item is fairly flat and no higher than 50 mm, then a surface detector is probably your best choice. Poorly maintained machines, the general wear and tear of the production machines are just a few of the ways that metal can enter your production process, ruin your grinder blades causing you thousands of dollars in production shutdowns.

Metal Detectors for Conveyor SystemsTo remove metals from your production process, a complete and total inspection of preassembled products is required to prevent these metals from leaving the plant and causing further damage. One possible solution involves examining the products at the end of the production line. Since all your products have to be transported to a conveyor belt at one time or another, a surface detector would be ideal for examining them while they are being moved to the conveyor.

Surface detectors are typically installed under the running belt cover. They can detect metal in the products above the running belt cover, but only in products that are not higher than 50 mm. Because they are located under the belt, they are not suitable for inspecting higher products, since their sensitivity decreases as the distance increases. The taller the product the less effective a surface detector will be. Anything higher than 50 mm is best analyzed by a tunnel detector.

MESEP RE

We offer a variety of surface detectors with varying detection capabilities in various module shapes. Choosing the right surface detector depends on the kind of product, its height and the type and size of metal to be detected. The MESEP AR surface detector is designed to be installed on a belt or shute conveyor. Only 35 mm high, this metal detector can be installed in places where space is limited. Available in three different sizes, these flat sensors can be installed side by side allowing you to scan a larger area. These detectors can also be arranged below and above the conveyor belt increasing the level of sensitivity.


Special Characteristics Installation
  • Very flat enclosure
  • Easy to Install.
  • No metal free zone
The MESEP® RE can be installed flush in metal. That means: Metal may touch the sensor casing laterally and from below. However, it must not project over the sensor area.

Metal Detectors for Conveyor Systems

Metal Detectors for Conveyor Systems

Model Name MESEP RE 350
Cable length 2 m
   
Installation flush
Detection width 350 mm
Installation height 30 mm
   
Sensitivity adjustable by Max Distance to sensor surface [mm]
Fe - plate 220 x 330 x 1 mm 150
Fe - plate 30 x 30 x 1 mm 70
Fe - plate 12 x 12 x 1 mm 50
Nut M 6 40
Washer for M 4 29
Nut M 4 18
Fe-bullet Ø 3.5 mm 15
Fe-bullet Ø 3.0 mm 12
Fe-bullet Ø 2.0 mm 6
Speed of detection 1 - 30 m/min
   
Electrical connection -
Operational voltage Ub 15 V DC
Load current only possible with amplifier
Ambient temperature -10° C... +60° C
Protection class IP 67
Active surface Polyurethane
Housing Material Alumimum casting
Connection PVC, cable 3 / 0.14
Required Accessories Control unit vide 8100 - 4000 or 8100 - 1900

*Sensitivity levels will decrease because of product effects.
Send test material if you think your product is magnetically permeable or conductive.

Metal Detectors for Conveyor Systems

For more technical information takes it please the chapter accessories under the point M-Pulse control electronic.

Metal Detectors for Conveyor Systems

Contact us today: - Tel: 973.227.0700


We accept the following major credit cards:

Plastic Process Equipment


Plastic Process Equipment

23 Spielman Road, Fairfield, New Jersey, USA, 07004-6155
Tel: 973.227.0700 ~ Fax: 973.227.7307 ~ Email: