MPULSE FL Surface Detectors for Conveyor SystemsSurface Metal Detectors

The Mpulse FL Surface detector is for detecting metal in particle boards and textiles. It is ideal for detecting some of the smallest metals such as needles and slivers. Surface metal detectors for conveyor belts are electronic devices for detecting the presence of unwanted metal contamination in items moving along a conveyor belt. If you're worried about metal contaminants entering your process, and the conveyed item is fairly flat and no higher than 50 mm, then a surface detector is probably your best choice. Poorly maintained machines, the general wear and tear of the production machines are just a few of the ways that metal can enter your production process, ruin your grinder blades causing you thousands of dollars in production shutdowns.

To remove metals from your production process, a complete and total inspection of preassembled products is required to prevent these metals from leaving the plant and causing further damage. One possible solution involves examining the products at the end of the production line. Since all your products have to be transported to a conveyor belt at one time or another, a surface detector would be ideal for examining them while they are being moved to the conveyor.

Surface detectors are typically installed under the running belt cover. They can detect metal in the products above the running belt cover, but only in products that are not higher than 50 mm. Because they are located under the belt, they are not suitable for inspecting higher products, since their sensitivity decreases as the distance increases. The taller the product the less effective a surface detector will be. Anything higher than 50 mm is best analysed by a tunnel detector.

Surface Metal Detectors Surface Metal Detectors Surface Metal Detectors

MPULSE FL

We offer a variety of surface detectors with varying detection capabilities in various module shapes. Choosing the right surface detector depends on the kind of product, its height and the type and size of metal to be detected. The MESEP AR surface detector is designed to be installed on a belt or shute conveyor. Only 35 mm high, this metal detector can be installed in places where space is limited. Availabe in three different sizes, these flat sensors can be installed side by side allowing you to scan a larger area. These detectors can also be arranged below and above the conveyor belt increasing the level of sensitivity.



Model Name M-Pulse FL
   
Mounting  
Installation typical horizontal, but each angle is applicable
-  
Metal free zone Fix metal = 300 mm [10*]
In front / behind of the detector Moving metal = 500 mm [20*]
   
Application Conditions  
Operational voltage 230 V / 50 Hz (others at inquiry)
Power input 40 Watt
Ambient temperature -0° C...+50° C/0...120 F
Product [food] temperature -0° C...+80° C/0...180 F
Protection class IP 65
Sensore head Stainless steel
Control electronics Stainless steel housing [prepared for wall fastening]
Link Cable 2.5 m mit cable protection tube [max. 3 m possible]
Conveyor speed 25-2000 mm/sec. [1" - 6.6 feet/sec.]

Sensitivity [Max. sensitivity - depending on product effects and proper installation]
Sensing width 200 - 1000 mm in 50 mm step-by-step
Height above sensor mm 10 20 30 40 50 60 70 80
Fe-ball Ø mm 0.8 1.0 1.8 2.2 2.5 3.8 5.0 6.0
Sensing width 1000 - 4000 mm in 50 mm step-by-step
Height above sensor mm 10 20 30 40 50 60 70 80
Fe-ball Ø mm 1.0 1.5 2.2 3.0 3.4 5.5 7.0 8.0
Non-ferrous app. 1.2 x ferrous-ball Ø
Stainless steel app. 1.5 x ferrous-ball Ø

Contact us today: - Tel: 973.227.0700


We accept the following major credit cards:

Plastic Process Equipment


Plastic Process Equipment

23 Spielman Road, Fairfield, New Jersey, USA, 07004-6155
Tel: 973.227.0700 ~ Fax: 973.227.7307 ~ Email: